Jump to content

Revisiting truck AC issue


Recommended Posts

At the end of last summer, my truck AC began to take longer and longer to blow cool air.  I'd be 10 mins into a drive before it cooled.  

I topped out the unit with Freon, and things seemed fine; however, I only probably ran it for another couple of weeks before the weather cooled.  The problem has begun to recur this summer.  

One thing I've noticed is that it seems to struggle with higher ambient temps.  On the way to school, it blows somewhat cooly rather quickly.  In the afternoon (90's) it struggles to overcome the higher temps.  It'll be 15 mins before it blows cool enough to bring the cab temp down.  Even then, it's not super cold.

Anyway, just wondering if the specific issues noted are enough to possibly pinpoint what I'm dealing with.  As you can see, I know next to nothing about vehicle AC systems.  I'd, at least, like to sound like I know what I'm talking about if I need a mechanic.  Thanks in advance.

 

Link to comment
Share on other sites

On 5/20/2023 at 8:59 PM, Jkwellborn said:
Make sure the the valves on the hoses seal up like they’re supposed to.

What vehicle were we talking about again?

This is a good first step.  Run the a/c and then pull the caps off of the high and low pressure values.  If there is moisture in the caps, you need to have the valves replaced.  

I installed a cut-off valve for the heater hose in my truck.  It takes longer to cool the cab if you have hot water running through the cab in the summer.*

*ETA - your truck is likely not 54 years old, so you might not want to start messing with the heater hose system.




dd5c7e4d94acdbb0d37832a80eba38c6.jpg

Edited by Jerry Callo
  • Hook 'Em 1
  • Haha 1
Link to comment
Share on other sites

  • 1 year later...

NecroBump:

Looking for an Austin area repair shop that specializes in AC work & I don't mean the compressor.

The dash is already cracked (badly) & the "blend door" stuff behind the glove box that controls the hot // cold mix is apparently my primary issue (including an occasional sort of "buzzing" or hum from the fan).

If I'm gonna replace the dash (stupid expendive) & an AC specialist will have to go down through the top, I should probably have the AC fixed @ the same time.

The closer to Dripping Springs (or South Austin) the better, however I would probably go as far as New Braunfels or Round Rock for the right shop.

Link to comment
Share on other sites

You sure it’s the blend door itself and not the actuator that moves it? You don’t need an AC shop for that. Have your mechanic do it. The actuators are easy to change on some vehicles. The blend door is more of a pain. I’ve got a broken one on my 97 and I’m not paying to have the dash pulled apart.

Link to comment
Share on other sites

2 hours ago, Jkwellborn said:

You sure it’s the blend door itself and not the actuator that moves it? You don’t need an AC shop for that. Have your mechanic do it. The actuators are easy to change on some vehicles. The blend door is more of a pain. I’ve got a broken one on my 97 and I’m not paying to have the dash pulled apart.

It's more likely a vacuum leak.  The actuators are vacuum controlled, and the plastic hoses tend to crack. 

Link to comment
Share on other sites

It's more likely a vacuum leak.  The actuators are vacuum controlled, and the plastic hoses tend to crack. 

Pretty sure it’s vehicle dependent. My 97 has a rod that connects it. There isn’t a vacuum hose going to it. There are two on the truck so I guess it’s possible.
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...